Shellab SRI20P Instrukcja Użytkownika Strona 1

BOD INCUBATORS 100 - 120 Voltage Installation and Operation Manual SRI3P, SRI6P, SRI20P Previously designated as LI3PW, LI6P, LI

10 | P a g e INSTALLATION This incubator is intended for use indoors, at room temperatures between 15C and 30C (59F and 86F), at no greater t

. 11 | P a g e INSTALLATION (CONTINUED) INSTALL SIDE AIR DUCTS, SRI20P Two (2) side air ducts are packed with the accessories of the SRI20P. I

12 | P a g e INSTALLATION (CONTINUED) SHELVING INSTALLATION SRI3P Shelf Installation Perform the following steps to install the SRI3P incubato

. 13 | P a g e INSTALLATION (CONTINUED) SRI6P and SRI20P Standard Shelving Installation Perform the following steps to install the SRI6P and SRI

14 | P a g e INSTALLATION (CONTINUED) SRI6P and SRI20P Sliding Shelf Installation Note: The SRI6P does not come with a sliding shelf. Sliding she

. 15 | P a g e INSTALLATION (CONTINUED) 3. Repeat the process on the opposite side of the chamber with the second sliding mounting bracket. 4.

16 | P a g e CONTROL PANEL OVERVIEW Figure 10: Control Panel SRI3P Power Switch The main power switch on the control panel (green lighted I/O) c

. 17 | P a g e OPERATION THEORY OF OPERATION Each SRIP incubator uses a Peltier thermoelectric cooling-and-heating device and an air circulating

18 | P a g e OPERATION (CONTINUED) SETTING UP THE INCUBATOR Perform the following steps and procedures to prepare the incubator for use each tim

. 19 | P a g e OPERATION (CONTINUED) CALIBRATE THE TEMPERATURE DISPLAY Allow the incubator at least 24 hours to stabilize at its operational se

2 | P a g e Sheldon Refrigerated BOD Incubators 100 – 120 Voltage Installation and Operation Manual Revision: April 29, 2014 Pictured on Cover: SR

20 | P a g e OPERATION (CONTINUED) SET THE OVER TEMPERATURE LIMIT Perform the following steps to set up the Over Temperature Limit system for use.

. 21 | P a g e OPERATION (CONTINUED) HUMIDIFYING THE INCUBATOR Placing only a small number of petri dishes or open media containers in the incu

22 | P a g e USER MAINTENANCE Warning: Prior to any maintenance or service on this unit, disconnect the power cord from the power supply. Avertiss

. 23 | P a g e MAINTENANCE (CONTINUED) Periodically, inspect the door latch, trim, catch, and gasket for signs of deterioration. Failure to maint

24 | P a g e UNIT SPECIFICATIONS These incubators are 100 - 120 voltage units. Please refer to the incubator’s data plate for individual electrical

. 25 | P a g e UNIT SPECIFICATIONS (CONTINUED) SHELF CAPACITY BY WEIGHT Model Per Shelf Total SRI3P 35lbs / 15.9kg 70lbs / 31.7kg SRI6P 75lbs / 3

26 | P a g e PARTS AND CONSUMABLES Description Part Number Feet, Adjustable Glide 2700506 Power Cord, USA 1800510 Shelves (2) SRI3P 6800529 Shelf

. 3 | P a g e TABLE OF CONTENTS INTRODUCTION ...

4 | P a g e INTRODUCTION Thank you for purchasing a Sheldon Manufacturing refrigerated BOD Peltier incubator. We know that in today’s competitive m

. 5 | P a g e INTRODUCTION (CONTINUED) ENGINEERING IMPROVEMENTS Sheldon Manufacturing continually improves all of its products. As a result, eng

6 | P a g e RECEIVING YOUR INCUBATOR Before leaving the factory, all incubators are packaged in high-quality shipping materials to provide protect

. 7 | P a g e RECEIVING (CONTINUED) RECORDING DATA PLATE INFORMATION Locate the data plate on the back of the incubator on the top right. The dat

8 | P a g e GRAPHIC SYMBOLS The incubator is provided with graphic symbols on its interior and exterior surfaces. These symbols identify hazards, a

. 9 | P a g e GRAPHIC SYMBOLS (CONTINUED) Symbol Definition WEEE Directive compliant logo Indicates the unit should be recycled (Not disposed